RIKENSOKUHAN CO.,LTD.ปiฤเ
 Thickness gauge. Japanese Industrial Standards combination list Thickness gauge. General article combination list |
THICKNESS@TypeA and TypeB | |
| 1. It is less than thickness 3mm, and this standard prescribes it about the gap gauge (following leaf) of simple substances less than 300mm inlength and a gap gauge (put together a gap gauge) that I put together. 1. The kind of kind thickness assumes it two kinds of the A form, B form by the shape of the leaf. 2. It is used to measure function distance and can inspect two minute plane space that I cannot measure with other measuring instruments easilyand exactly. 3. It is a tool for measurement that the indispensableness is not made for a use car and a motor, the distance measurement of the piston andcylinder part between the motor |
 Company handling list |
THICKNESS TAPE |
|
| 1. There are two kinds of materials SK and SUS304. 2. I am used if for adjustment such as the assembling of a function automobile engine and other machines and am effective at all in thecontinuation measurement of the single gap. I usually produce 12.7 width special width and the special thickness processing. I process copper, brass, the phosphorus bronze other than it. |
 Various liner. company handling list |
rj liner and rtr liner | |
| 1. There are two kinds of materials SK and SUS304. Width - 300mm 2. It is rikensokuhan original special size stainless steel . I process copper, brass, the phosphorus bronze other than it. |
 The shape of one side of the story scissors and dimensions The shape of C form scissors and dimensions Both mouths scissors shape and dimensions |
Limit scissors gauge | |
| 1. There are two kinds of kind one side of the story form and both mouths form. 2. And super obstinate materials we standard SKS (I produce it in answer to other needs.) I produce the equal processing with the step of theboard thickness and width and measurement department. 3. Super hard HRC60 +-2 about hardness SKS: I am superior in abrasion characteristics, and long usage is possible. 4. An expectation is to the public establishment and uses the mouth of the function gauge though I inspect it whether you enter between theupper limit and the lower limit that a cylindrical spherical diameter, the thickness of the cuboid can permit. It is one of the gauges that I cannot miss for inspection in large quantities. |
 The shape of the limit plug gauge and dimensions The shape of the limit plug gauge and dimensions The shape of the board plug gauge and dimensions |
Limit stopper gauge | |
1. There are two kinds of kind one side of the story form and both mouths form. In addition, there is the monomorphism, too. 2. Materials we standard SKS and super hard and hard chromeplating and ceramic (I produce it in answer to other needs.) 3. Super hard HRC60 +-2 about hardness SKS: I am superior in abrasion characteristics, and long usage is possible. It may not be stronglyrusted in hard chromeplating water. 4. The good or bad can judge the hole diameter which is function high precision easily. It is one of the gauges that I cannot miss for inspectionin large quantities. It is a street, a gauge measuring for stopping dimensions clearance. |
 The shape of the limit ring gage and dimensions A master ring gage shape and dimensions |
Limit ring gage | |
1. I stop, and and a set is unitary a street. 2. And super obstinate our standard SKS (I produce it in answer to other needs.) 3. Super hard HRC60 +-2 about SKS: I am superior in abrasion characteristics, and long usage is possible. 4. A gauge for inspection to use in combination two gauges of a greatest dimension and the smallest dimensions for to finish completiondimensions within the uniformity when I perform manufacturing of the dimensions standard master large quantity production of the comparativemeasurement / check management. |
 The shape of various taper gauges and dimensions |
Taper gauge | |
| 1. A gauge scale to be used for measurement use of the inside diameter hole diameter of the pipe using taper of the kind width is ticked away.There is the internal taper gauge measuring using thickness. I process the cylindrical taper. |
 |
It is a gauge other than it | |
A spacer produces an outer diameter ring in the needs of the visitor other than it a figure gauge byte liner a block gauge a roller gauge a keywaygauge in total. |
|
 NIGATA RIKENSOKUHAN CO.,LTD. |
|
Precision level, right angle ruler, prejudiced mind tester, protractor straight edge, others, |
TRADE
MARK RIKENSOKUHAN CO.,LTD.
163-1sunaharacho.nishiku.nagoya-shi.aichi.452-0811.JAPAN TEL+81-52-503-1251 FAX+81-52-503-1522 E-mail info@r-s-k.co.jp@@@@@@@@@@@@@@@@@@@@@@Go to the top of this page@